1. Two markets, two machines
A home groomer clips one dog every few weeks; a salon runs a machine four to six hours a day through dirty, matted, sometimes damp coat. That duty cycle — not the number of speeds on the box — is what separates the two builds. Our clipper and trimmer range covers both; this is the specification underneath the listing photo.
Moving up buys continuous duty in a metal housing, a detachable blade, and a parts list the buyer asks about before asking the price.
2. The blade system is the product
Buyers compare machines; groomers compare blades. The system you choose decides your replacement revenue for years. A5 detachable blades release with a lever; integrated or 5-in-1 heads slide the cutter instead — cheaper, and when the cutter dulls the repair is often the whole head.
| Blade | Coat left | Typical use |
|---|---|---|
| #40 | 0.25 mm | Veterinary preparation — not a body length |
| #30 | 0.5 mm | Base blade under snap-on combs |
| #15 | 1.2 mm | Faces, feet, close detail |
| #10 | 1.5 mm | Sanitary areas and paw pads — the all-rounder |
| #9 | 2.0 mm | Short body work |
| #7F | 3.2 mm | Short body clip, the popular pet length |
| #5F | 6.3 mm | Medium-short body finish |
| #4F | 9.5 mm | Longer trim on prepared coat |
| #3F | 13 mm | Longest detachable option |
The numbering runs backwards — a higher number leaves less coat — while the plastic combs that clip over a blade run the other way, No.1 at 3 mm to No.8 at 25 mm. Customers get this wrong constantly, so a printed blade-and-comb chart on the box reduces returns. Pin down blade width (45 mm standard, 50 mm for large breeds) and written confirmation that the combs in the carton fit it.
3. Strokes per minute is not a speed
Pivot motors are quoted in strokes per minute, rotary motors in rpm, and the figures are not comparable: 7,200 SPM is not twice 3,600 rpm, and a pivot motor sheds torque under load. Ask for speed under load — it should stay above about 70 per cent of free-run speed. Below that the motor is undersized, and the buyer feels a machine that bogs down.
Stall torque matters wherever matting is normal: target about twice rated load torque. State duty cycle in minutes — ten on, ten off for home, continuous for salon. A quotation without one is a home-duty quotation.
4. Noise is the feature that sells it
Most dogs fear the noise before the blade, which is why quiet commands a premium — and why "low noise" needs a method: dB(A) at 30 cm from the housing, under load, with background below 30 dB(A). Under 60 is a quiet home unit; 60 to 70 is ordinary; above 70 is salon-normal, not a selling point.
Free-run figures flatter every machine, since the blade chattering through coat is the loud part — test loaded, publish loaded. Vibration belongs beside it: an accelerometer reading on the housing, and the bench test of a coin standing on the casing at full speed. It is what aches a wrist by week three.
5. Heat at the blade
Steel against steel gets hot: ten minutes of continuous clipping can put the blade at 50 to 60 °C, uncomfortable on skin and risky on a thin coat. Steel cutters are durable and re-sharpenable; ceramic runs cooler but chips if dropped. Airflow is the second lever — grooved blades, fan-assisted cooling, or a spacer that lifts the cutter off the skin.
Under IEC 60335-2-8 the hot-blade warning is not automatic: the standard allows the label to be omitted where measured temperatures stay inside its limits, a result you can quote and defend. Check it with a ten-minute run at 25 °C ambient, reading the blade at one, five and ten minutes.
6. Battery, cord and the paperwork behind them
Three builds: mains cord, cordless on a charging stand, USB-C rechargeable. The middle carries the most return risk: the battery is the part you cannot inspect on the line. Specify capacity in mAh, runtime under load rather than at idle, charge time, a protection board, plus UN 38.3 and IEC 62133.
Those two are what a forwarder asks for before a lithium battery flies; our shipping guide covers the rest. Voltage is a sourcing decision: 100–120 V for North America and Japan, 220–240 V for Europe, the UK and Australia. One universal adapter cuts SKUs but adds a failure point at the plug.
7. The certification file
- EU — LVD 2014/35/EU and EMC 2014/30/EU, tested to EN 60335-1 with EN 60335-2-8, the part that names animal clippers; RoHS 2011/65/EU; RED 2014/53/EU if there is Bluetooth; an EU responsible person on the label
- UK — UKCA to the same standards, plus a UK responsible person
- US — UL or ETL listing to the UL edition of the appliance standard, and FCC Part 15 for the adapter or any radio
- Battery — UN 38.3, IEC 62133, and EU Battery Regulation registration where you sell into the EU
None of this makes a machine cut well; the file only lets you sell it lawfully. Our compliance guide maps how the documents fit together.
8. Tests worth running before shipment
- Blade alignment on every unit — the defect behind most after-sales complaints, so not a sample item
- Ten-minute loaded run, blade temperature recorded at three points
- Noise at 30 cm under load, against the specification figure
- Drop from 900 mm onto a hard floor, then dielectric strength on the same unit
- Charge and discharge on five units, timed against claimed runtime
- Comb fit on the widest and narrowest blade in the set
- Plug, voltage and manual language checked against the destination market
Run these on the pre-shipment sample; the AQL and audit guide sets the sampling frame.
9. What to put on the purchase order
One page, attached to every repeat order:
- Blade system, blade width in mm, blades and cutter material per unit
- Comb lengths in mm, with written confirmation they fit that width
- Motor type, loaded speed, stall torque, duty cycle in minutes
- Noise target in dB(A), with test distance and load condition
- Battery capacity, loaded runtime, charge time, protection features
- Certification reports per market, and a Declaration of Conformity in the correct name
- Spares allowance — blades, drive levers, combs — priced as a percentage of the order
Specified this way, a clipper range stops being a commodity box. The machine that comes back is rarely the one that cut badly on day one; it is the one whose blade drifted, or whose battery was quoted at idle.