1. Pick the form factor before the materials
The construction decides which materials you can reasonably use, so settle this first:
- Mat / crate pad — flat, cheapest to make, lowest freight per unit. The default entry SKU for most importers.
- Bolster bed — raised sides, needs fibre-filled bolsters stitched to a foam or fibre base; the highest-volume shape in retail.
- Donut / cuddle bed — continuous fibre wall, shallow base. Harder to fill evenly, so the fill weight specification matters more than anywhere else.
- Orthopaedic mattress — foam-led rather than fibre-led, sold on density and support rather than softness. Highest margin, highest material cost.
- Cave / hooded bed — structure comes from panels, so it needs a stiffer interlining or a wire frame to hold its shape in transit.
Our own cat beds and car dog beds range covers all five shapes, and every one of them can be built to a spec sheet rather than an image.
2. Foam: density is the specification
"Memory foam" on its own means very little. Ask for the density in kg/m³ (or lb/ft³) and the compression or hardness figure, and treat any supplier who cannot quote both with caution. Low-density foam feels wonderful at the factory and turns to a flat slab in three months, which is how a returns problem starts.
| Foam type | Typical density | Best used for | Where it fails |
|---|---|---|---|
| Standard polyurethane | 25–35 kg/m³ | Crate mats, bolsters, cost-led lines | Compresses permanently under constant load |
| High-resilience foam | 35–45 kg/m³ | Bolster bases and everyday mats sold on durability | Higher cost; stiffer feel out of the pack |
| Viscoelastic ("memory") foam | 40–60 kg/m³ | Orthopaedic and senior-pet lines | Slow to re-loft; never vacuum-compress it hard |
| Egg-crate / convoluted foam | 20–30 kg/m³ | Lightweight crate pads and toppers | Very low load bearing; tears at the profile peaks |
| Shredded foam fill | Mixed | Refillable and "stuff your own" beds | Settlement over time; hard to quote a uniform fill weight |
If you sell into the US and want to talk about foam quality in marketing copy, specify foam from a mill that carries a recognised foam certification programme; the same logic applies to covers milled to a textile standard such as OEKO-TEX Standard 100. Ask for the certificate number, not the logo — see our compliance and certification map for what each market expects to see.
3. Fill: hollowfibre is not hollowfibre
Bolster walls and donut beds are filled with polyester fibre. Three numbers decide how the finished bed looks and survives washing:
- Fabric weight (GSM) — 200–250 gsm gives a soft, settling pillow; 300–400 gsm holds the wall upright and survives repeated washing.
- Fill weight per bed — specify it in grams per size, with a tolerance. This is the single number suppliers quietly reduce between the sample and mass production.
- Fibre type — siliconised hollowfibre for loft, recycled PET fibre where your market values recycled content, and crimped fibre where you only need volume.
Other fill options worth knowing: cooling gel layers and phase-change pads for summer lines, and reflective self-warming interliners, which buyers often mistake for electrical heating. Neither is an electrical product, but both carry marketing claims — keep the wording factual and avoid implying a therapeutic outcome.
4. Cover fabric and the coating nobody sees
The cover is what the customer judges, and the coating is what decides whether the bed comes back. Specify both layers:
- 600D Oxford with PU coating — the workhorse for waterproof and easy-clean beds. 300D is lighter and cheaper; 1680D is heavier and more abrasion resistant.
- Plush, sherpa or faux fur — best measured by pile height and GSM. Short pile cleans better; long pile photographs better.
- TPU or PUL inner lining — a true waterproof layer between cover and foam. A PU coating alone stops spills, not saturation.
- Anti-slip base — silicone dots or rubberised mesh. Cheap to add, and a visible difference in store.
5. Construction details that prevent returns
- Covered zipper flap. An exposed zipper is the first thing a bored dog chews. Specify a flap and a lockable or recessed slider.
- Removable, machine-washable cover at a stated temperature, with the care label matching the claim on the pack.
- Double-stitched seams at load points, plus a stated seam strength result if the line is sold on durability.
- Foam insert in a fitted liner, so the foam can be replaced instead of the whole bed being written off.
- No loose fibre migration — felt the inside of the cover after a wash test; wiring fibre through a seam is a common complaint on low-cost lines.
6. Publish a size chart that maps to crate sizes
Sizing is where a bed line loses money. Retailers buy the wrong ratio of sizes when the chart is only in centimetres, so give both measurements and a reference point:
| Size | External (cm / in) | Reference |
|---|---|---|
| Small | 50 × 40 / 20 × 16 | Small cats, toy breeds up to ~5 kg |
| Medium | 70 × 50 / 28 × 20 | Fits a 24–30 inch crate; small-to-medium dogs |
| Large | 90 × 60 / 35 × 24 | Fits a 36 inch crate; medium dogs |
| X-Large | 110 × 70 / 44 × 28 | Fits a 42 inch crate and larger; large breeds |
7. Packing and freight: the volumetric trap
Beds are soft, bulky and light, which makes them the classic volumetric-weight problem in a container or a courier network. Two practical levers:
- Vacuum compression in a printed poly bag, packed flat, typically removes 50–70% of the volume of a fibre bed. Always ask for the post-compression recovery time on paper — some foam needs a day or more to re-loft, which is fine in a warehouse and a problem in a retail display.
- Carton cube efficiency over carton count. A carton holding 10 beds at 96% fill beats 8 beds at 70% fill, even if the unit price looks higher.
The maths follows the same logic as any bulky pet line — our freight guide walks through how carriers apply volumetric divisors, and the packaging guide covers how to brief compressed retail packaging that still protects the product.
8. What to test before you commit
- Wash test — three cycles at your stated temperature: check shrinkage, colour bleed, pile matting, seam integrity and fibre migration.
- Fill weight audit — weigh the fill of the production sample against the approved sample, per size.
- Foam recovery — compress, release, and measure thickness return after 15 minutes and after 24 hours.
- Colour fastness to rubbing and washing — especially on deep navy, black and red covers, which are repeat offenders.
- Coating adhesion — for waterproof claims, a simple penetration test on the liner tells you more than a marketing sheet.
Every line we export can be specified down to the fill weight and coating type, with OEM and ODM options through our OEM / ODM service if you want the shape, size chart or packaging changed rather than just branded.
Bottom line
Write down the foam density, the fibre weight and the liner material. Approve a physical sample, keep it sealed, and inspect mass production against it. Beds are simple products that fail for unglamorous reasons — and nearly every one of those reasons is a number that was left out of the specification.