1. "IATA approved" is a specification, not a certificate
The International Air Transport Association publishes the Live Animals Regulations, which include the container requirement for dogs and cats — the standard widely known as CR 82. It covers construction, ventilation, sizing, doors, floors and labelling. What it does not do is certify products: IATA explicitly does not approve, endorse or sell any crate brand or model. There is no official stamp, and any listing that claims one is marketing.
The honest pitch is "built to IATA requirements", backed by a specification you can show a buyer. Airlines can and do add their own rules on top — size ceilings on certain aircraft, embargo policies on snub-nosed breeds in hot months, weight limits — so the crate that passes one route needs margin on every clause, not a bare pass.
2. Sizing: the formula your retail customers will use
Airlines size crates from four body measurements. Publish this table on your pack or insert, because most sizing returns come from buyer confusion rather than product failure:
| Measure | Definition |
|---|---|
| A | Nose to the base of the tail, tail excluded |
| B | Ground to the elbow joint, standing naturally |
| C | Widest point of the body, usually across the shoulders |
| D | Floor to the top of the head or ear tips, standing — use the larger of the two |
The minimum internal crate dimensions follow directly: length A + ½B, width C × 2, height D plus an allowance for bedding. A large dog measuring 75, 25, 45 and 68 cm across those four points therefore needs roughly 88 × 90 × 70 cm internally. Two adjustments matter commercially: brachycephalic (snub-nosed) breeds need a crate 10% larger than the formula gives, and long-haired breeds need height measured to the coat, not the skin.
For a wholesale range, the practical consequence is the size ladder. Seven or eight sizes from toy-breed to giant, each clearly labelled with the measurement band it serves, converts better than a short run of "small / medium / large" — and each size ships as its own carton, so brief the full carton matrix early.
3. Ventilation: the number airlines check
- 16% ventilated area across the four sides is the figure carriers and pet shippers commonly verify. Moulded slots count; measure them, do not estimate.
- Maximum opening size — around 25 × 25 mm for dogs and 19 × 19 mm for cats, small enough to be nose- and paw-proof.
- Welded mesh inserts over ventilated areas must be securely fixed so the animal cannot dislodge them from inside.
- All four sides ventilated for international transport, with openings weighted toward the upper portion of the walls.
When you adapt an existing mould or copy a competitor's bestseller, do not assume the ventilation carries over. Put the shell on a gridded board and measure the actual open area before you claim compliance — it is a five-minute check that prevents a very expensive listing.
4. Doors, hardware and construction details
Check-in staff judge a crate on its hardware in about thirty seconds. These are the details that decide it:
- Metal nuts and bolts joining the two shell halves. Plastic clips or nylon fasteners as the sole fixing are refused by most carriers.
- Locking pins that engage the frame by at least 1.6 cm and cannot be worked open from inside.
- A rigid hinged door in a strong frame — not a sliding panel, and never a zippered soft front.
- Wheels removed or disabled for flight. Design them detachable so the crate still rolls in the showroom.
- A solid, leak-proof floor with room for absorbent bedding underneath the animal.
- Food and water dishes fixed inside but refillable from outside, without opening the door.
- Clear label real estate on the shell for "Live Animals" and directional arrows.
5. Materials worth specifying
Most airline-style crates are injection-moulded polypropylene, and the resin decision is where cheap lines are born. Virgin PP keeps its impact resistance at low tarmac temperatures; heavy recycled content can turn brittle in the same conditions. Ask for wall thickness at the ribs and corners, not just an average, and confirm the rim profile lets the two halves stack without pinching. Hardware should be plated or stainless, with a small spare-bolt bag in the box — a lost bolt at check-in is the same missed flight as a broken latch.
6. What to test before mass production
- Dimension audit — every size measured against the sizing formula and printed on the insert.
- Door cycle and pin engagement — repeated open-close plus a pull test on the locked door.
- Drop or impact test — a loaded crate tipped and dropped from handling height, checking shell and latch integrity.
- Stack test — two loaded crates stacked, confirming the rim ribs carry the load.
- Ventilation measurement — actual open area as a percentage of the four sides.
- Hardware torque — bolts torqued and re-checked after a vibration cycle.
Approve against a sealed sample and inspect production against it — the workflow is the same one we describe in our golden sample guide, and the factory-side checks belong inside the supplier audit you run before the deposit.
7. Freight: shipping crates that are themselves cargo
Travel crates are bulky, and freight is where the line's margin lives or dies. Nest the upper half inside the lower half on every unit, confirm the stacked set cannot scuff in a printed retail carton, and ask for CBM per size so you can plan the container — our loading checklist covers the stacking and supervision side. Our own pet cages and crates range includes both folding wire models for retail and rigid travel crates, and every size can be quoted with its carton matrix and OEM branding options.
Bottom line
An airline crate earns its price at a check-in counter you will never see. Build to the IATA clauses, test against them, publish the sizing formula, and say "built to IATA requirements" instead of "IATA approved" — it is more accurate, and it is the claim that survives scrutiny.